Sioux-tools TP9A Manuale Utente Scaricare il pdf

Printed In U.S.A.

INSTRUCTIONS & PARTS LIST FOR TP9A SERIES TAPPERS

SERIAL C

Read and understand "Safety Instructions For Air Tools" and these instructions before

operating this tool.

Form ZCE640B

Date 2004July1/A

Page 1 of 18

AIR SUPPLY

The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure

regulator, and lubricator will insure maximum output and life of tools. Before connecting tool, blow out the air line to remove water

and dirt which may have accumulated.

HOSE AND HOSE CONNECTIONS

Supply hose should be not less than 1/4" (6.4 mm) I.D. Extension hoses should be at least 3/8" (10 mm) I.D. Use couplings and

fittings with at least 3/8" (10mm) I.D.

LUBRICATION

Use SIOUX No. 288 air motor oil. An airline lubricator, set to deliver 2 to 4 drops per minute, is recommended. If a lubricator is not

used, add .04 oz. (1.2cc, 12 to 15 drops) of oil into the air inlet twice daily.

Lubricate the gearing every 100 hours of operation with SIOUX No. 289A grease.

GENERAL OPERATION

The direction of spindle rotation is controlled by the reversing button. When the button is depressed, the spindle rotates

counterclockwise. Always depress the button fully to obtain full power. The reversing button can be locked in the

reverse direction by fully depressing and rotating the button clockwise.

TO INSTALL A TAP

 Remove rubber collet and collet nut from the chuck body.

 Loosen back jaws with a hex wrench.

 Insert tap into chuck body so that the tap driving square is in the back jaws.

 Tighten the back jaws onto the tap driving square with a hex wrench.

 Install the rubber collet and collet nut over the body of the tap and tighten with an open end wrench.

TO TAP A HOLE

 Make sure the hole to be threaded is the proper size for the tap.

 Apply a thread cutting lubricant.

 Hold the tap square and in line with the hole.

 Start the tool.

 When the tap reaches the desired depth, press the reverse button on top of the tool to reverse the rotation of the tool.

Certain conditions and materials may cause the tap to stick, causing a sudden movement of the tool.

Be ready for this movement. Have a firm footing at all times. Keep a firm grip on the tool at all times.

Sudden movement of the tool can cause injury.

When the rotation of the tool is reversed, the force on your hand will reverse.

Be ready for this reverse force. Have a firm footing at all times. Keep a firm grip on the tool at all times.

Reversal of force can cause injury.

1 2 3 4 5 6 ... 18 19

Sommario

Pagina 1 - SERIAL C

1Printed In U.S.A.INSTRUCTIONS & PARTS LIST FOR TP9A SERIES TAPPERSSERIAL CRead and understand "Safety Instructions For Air Tools" and

Pagina 2

10*Pression acoustique *Puissance acoustique *VibrationCatalog No. dBA dBA m/s2TP9A-4 77,9 89,5 Moins de 2,5TP9A-7 77,9 89,5 Moins de 2,5TP9A-25 77,9

Pagina 3 - C-SERIE

11INSTRUCTIES EN ONDERDELENLIJST VOOR TP9ASERIE CVoordat u de machine in werking stelt, moet u deze instructies en deVeiligheidsvoorschriften voor

Pagina 4

12Catalogus- *Geluidsdruk *Geluidsvermogen *Trilling nummer dBA dBA m/s2TP9A-4 77,9 89,5 Minder dan 2,5TP9A-7 77,9 89,5 Minder dan 2,5TP9A-25 77,9 89,

Pagina 5

13ANVISNINGAR OCH RESERVDELSLISTA FÖR TP9ASERIE CLäs och sätt dig in i Säkerhetsföreskrifter för tryckluftsverktyg samt dessa anvisningarinnan du

Pagina 6

14*Ljudtryck *Ljudeffek *VibrationKatalog nr. dBA dBA m/s2TP9A-4 77,9 89,5 Mindre än 2,5TP9A-7 77,9 89,5 Mindre än 2,5TP9A-25 77,9 89,5 Mindre än 2,5*

Pagina 7

15FURNISH CATALOG, SERIAL, AND MODEL NUMBERWHEN ORDERING PARTS*Order Quantity As RequiredFig. PartNo. No. DescriptionPARTS LIST FOR TP9A SERIES TAPPER

Pagina 8

16272611121314151617181920212223242510151515171718202829303132333435897123456Fig. PartNo. No. DescriptionFig. PartNo. No. Description*Order Quantity A

Pagina 9 - CLASSE C

17121314151617181920211089712345622232425262728291411Fig. PartNo. No. DescriptionFig. PartNo. No. DescriptionPARTS LIST FOR TP9A SERIES TAPPERS(SINGLE

Pagina 10

18Printed In U.S.A.Der durch Elektrosanden, -sägen, -schleifen und -bohren sowie durch andere Bauarbeiten anfallendeStaub enthält Chemikalien, die nac

Pagina 11 - SERIE C

This pdf incorporates the following model numbers: TP9A-4C32

Pagina 12

2*Sound Pressure *Sound Power *VibrationCatalog No. dBA dBA m/s2TP9A-4 77.9 89.5 Less than 2.5TP9A-7 77.9 89.5 Less than 2.5TP9A-25 77.9 89.5 Less tha

Pagina 13

3ANWEISUNGEN & TEILELISTE FÜR TP9AC-SERIEVor dem Betrieb dieses Werkzeugs lesen Sie bitte diese Anweisungen und dieSicherheitsanweisungen für D

Pagina 14

4Katalog *Schalldruck *Schallstärke *VibrationNr. dBA dBA m/s2TP9A-4 77,9 89,5 Weniger als 2,5TP9A-7 77,9 89,5 Weniger als 2,5TP9A-25 77,9 89,5 Wenige

Pagina 15 - TP9A SERIES TAPPERS

5INSTRUCCIONES Y LISTA DE PARTES PARA TP9ASERIE CLea y entienda Instrucciones de seguridad para herramientas neumáticas y estasinstrucciones ante

Pagina 16 - SERIAL A

6No de *Presión de sonido *Potencia de sonido *VibraciónCatalogo dBA dBA m/s2TP9A-4 77,9 89,5 Menos de 2,5TP9A-7 77,9 89,5 Menos de 2,5TP9A-25 77,9 89

Pagina 17 - (SINGLE REDUCTION2500 RPM)

7ISTRUZIONI E LISTINO PARTI PER TP9ASERIE CLeggere attentamente le Norme di sicurezza per luso di attrezzi pneumatici e le seguentiistruzioni pr

Pagina 18 - Printed In U.S.A

8*Pressioine sonora *Potenza sonora *VibratzioniCatalogo n. dBA dBA m/s2TP9A-4 77,9 89,5 Inferiore a 2,5TP9A-7 77,9 89,5 Inferiore a 2,5TP9A-25 77,9 8

Pagina 19 - TP9A-4C32

9INSTRUCTIONS ET LISTE DES PIECES POUR TP9ACLASSE CAvant de vous servir de ce matériel, lisez soigneusement ces instructionsainsi que la fiche sécur

Commenti su questo manuale

Nessun commento

Sioux-tools TP9A Manuale Utente

Navigare online o scaricare Manuale Utente per Attrezzi elettronici Sioux-tools TP9A. Sioux Tools TP9A User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Attrezzi elettronici Sioux-tools TP9A